background image

60

en-US/C

A

 Time and date

 DatE/TIME

Time
Adjustment range: 00:00 ... 23:59
Factory setting: 12:00

 DatE/YYYY

Year
Adjustment range: 2010 ... 2099
Factory setting: 2010

 DatE/MM

Month
Adjustment range: 01 ... 12
Factory setting: 03

 DatE/DD

Day
Adjustment range: 01 ... 31
Factory setting: 15
The date and time can be entered. Both are required 
for the thermostat function.

ROSA

 ROSA 

ROSA numbers
Adjustment  range:  0000 ... 9999
In the ROSA channel, the 4-digit number given by the 
Online Service Assistant can be entered.
The following table shows the numbers available for 
the BX L with the corresponding system layouts.

System

ROSA number

ARR1

5

ARR2

16

ARR3

6

ARR4

17

ARR5

225

ARR6

226

ARR7

227

ARR8

29

ARR9

228

Valve logic

 VLOG

Valve logic
Adjustment range: 1, 2, 3, 4
Factory setting: 1
In this adjustment channel the valve logic can be 
adjusted.

Ventillogik 

1

 

2

 

 

4

Durchflussrichtung
im stromlosen Zustand

Ventillogik 

1

 

2

 

 

4

Durchflussrichtung
im stromlosen Zustand

Valve logic

Flow direction when the 
valve is normally open

Temperature unit

 UNIT

Temperature unit
Adjustment range: °C, °F
Factory setting: °C
In this adjustment channel the temperature unit can 
be chosen.
The unit can be switched between °C and °F during 
operation.

Summary of Contents for SCU345









































































Reviews: