background image

2 of 19 

 

 

 

CONTENTS 

 
 

DESCRIPTION 

 

PAGE 

Introduction ------------------------------------------------- 3 
Mounting Instructions 

------------------------------------------------- 3 

Safety notes 

------------------------------------------------- 3 

Connections to the telephone line 

------------------------------------------------- 3 

Dealing with other telephone equipment 

------------------------------------------------- 4 

Dealing with Broadband 

------------------------------------------------- 4 

Wiring directions 

------------------------------------------------- 5 

Connecting more than one handset 

------------------------------------------------- 6 

Lock release back EMF protection 

------------------------------------------------- 6 

Cable size 

------------------------------------------------- 7 

Jumper setting 

------------------------------------------------- 7 

Programming overview 

------------------------------------------------- 7 

Tones overview 

------------------------------------------------- 8 

Initial setup 

------------------------------------------------- 9 

Optional call adjustments 

------------------------------------------------- 10 

Setting the auxiliary outputs ------------------------------------------------- 10 
Advanced speech setup options 

------------------------------------------------- 11 

Dial in facility setup ------------------------------------------------- 11 
Divert call setup 

------------------------------------------------- 12 

Access code setup 

------------------------------------------------- 13 

Specialised setup 

------------------------------------------------- 13 

User commands 

------------------------------------------------- 14 

Approval ------------------------------------------------- 14 
Troubleshooting ------------------------------------------------- 15 
Specification ------------------------------------------------- 15 
Telephone connection examples 

------------------------------------------------- 16 

Wiring diagram 1 (837M amplifier) 

------------------------------------------------- 17 

Wiring diagram 2 (837 amplifier) 

------------------------------------------------- 18 

Wiring diagram 3 (VK6N) 

------------------------------------------------- 19 

 
 
 
 
 
 
 
 
 
 
 
 
 

SPECIFICATION:

 

Supply 

voltage 

  230V 

AC 

Max number of telephone 

 

Enclosure 

material 

  ABS 

plastic 

Dimensions 

  157.5mm(L) 

105mm(W) 

x 65mm(H) [Standard 9 module DIN box] 

+12V 

out 

   100mA 

Max 

Relay contacts 

 

 

2A DC, 2A AC resistive 

1A AC inductive - 24VDC 120V AC

 

Summary of Contents for ART380




















Reviews: