FR - F
rançais - M
anuel d
’instruc
tions
32
MNVCNXPTZT_1710_FR
Si les valeurs de Start et Stop du menu
Modifier zone sont à zéro, l’affichage du
texte est désactivé. En cas de superposition
de plusieurs zones, la zone portant le
nombre le plus haut prévaut.
Pour la définition de les aires suivre le sens
des aiguilles d’une montre comme illustré
en figure.
0°
Start1=15°
Stop1=45°
Start2=170°
Stop2=225°
270°
90°
180°
Fig.
46
Le nom et la position standards des aires
de la tourelle se réfèrent aux quatre points
cardinaux. La position du NORD se modifie
à l’aide du paramètre Offset Pan du menu
mouvement (9.1.6 Menu Mouvement, page
9.1.5.3 Menu Masquage
Le masquage dynamique permet de créer un
maximum de 24 masques de façon à obscurcir des
zones particulières définies par l’utilisateur.
Les masques sont définis dans l’espace et tiennent
compte de la position horizontale et verticale et de la
profondeur du zoom au moment de la configuration.
L'unité maintient automatiquement la position et
la dimension du masque en fonction de la zone
affichée.
Un maximum de 8 masques peut être affiché
simultanément.
Si le dispositif est utilisé à sa vitesse maximale, les
temps de mise à jour du signal vidéo deviennent
critiques et il est nécessaire de créer des masques
plus grands que l’objet afin de cacher ce dernier plus
longtemps durant le passage et d’éviter tout risque
de visualisation.
En vue d’un fonctionnement parfait, la
position en tilt du masque doit toujours
être comprise entre -70 et +70 degrés
et la dimension du masque doit être le
double de celle de l’objet (en hauteur et en
largeur).
Il permet de configurer les paramètres suivants :
1.
Couleur Masque:
Permet de sélectionner la
couleur des masques.
2.
Modifier Masques:
Permet d’accéder au sous-
menu Modifier Masques et de configurer les
paramètres de masquage dynamique.
MASQUAGE
------------------------
1>COULEUR : BLEU
2 MODIFIER MASQUES >
Fig.
47
Summary of Contents for NXPTZ
