Victron energy Phoenix Smart IP43 12/30 Manual Download | Manualshive

Page: 33 / 59

background image

6.4.4. Re-enabling Bluetooth

It is possible to re-enable Bluetooth using the MODE button.

To re-enable Bluetooth:

a. Depress and hold the MODE button (on the

Phoenix Smart IP43 Charger

) for 10 seconds.

b. After 10 seconds have elapsed all charge mode LEDs will blink twice to indicate that Bluetooth has been re-enabled, and all

Bluetooth settings reset.

During this procedure:

a. Bluetooth is re-enabled

b. The PIN code is reset to default (000000)

c. Any active Bluetooth connections are disconnected

d. All Bluetooth pairing information is cleared

Subsequently, before attempting to re-connect it’s also necessary to remove/clear the Phoenix Smart IP43
Charger Bluetooth pairing information from any devices (mobile phones or tablets) that were previously
paired.

Phoenix Smart IP43 Charger

Page 31

Setup

«
...
31
32
33
34
35
...
»

Summary of Contents for Phoenix Smart IP43 12/30




























































Reviews:

No comments

Related manuals for Phoenix Smart IP43 12/30

Brand: Samsung Pages: 5

Brand: Samsung Pages: 6

Brand: National Instruments Pages: 4

Brand: Macma Pages: 4

Brand: Clarke Pages: 12

Brand: GYS Pages: 32

Brand: Sunforce Pages: 1

Brand: LuminAir Pages: 4

Brand: NOCO Genius Pages: 15

POWER PEAK LIPOLY 300 EQ

Brand: ROBBE Pages: 28

Brand: Xantrex Pages: 62

Brand: Listen Pages: 2

Green Motion Building Pro

Brand: Eaton Pages: 24

Brand: NEC Pages: 71

Brand: HardWire Pages: 18

Deltaco QI-1037

Brand: Nordic Pages: 9

Brand: Wii Pages: 2

Brand: Perel Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands