manualshive.com logo in svg

Victron energy BlueSolar 100/30, Manual

Share
Download
Victron energy BlueSolar 100/30 Manual Download Page 56

10. Technical specifications

10.1. Specifications 100/30 and 100/50

MPPT 100/30

MPPT 100/50

Battery voltage (auto select)

12V or 24V

Rated charge current

30A

50A

Nominal PV power, 12V 

1a,b

440W

700W

Nominal PV power, 24V 

1a,b

880W

1400W

Maximum PV open circuit voltage

100V

100V

Max. PV short circuit current 

2

30A

50A

Maximum efficiency

98%

Self-consumption

12V: 30mA / 24V: 20mA

Charge algorithm

Multi-stage adaptive (eight pre-programmed algorithms) or user defined

algorithm

Charge voltage 'absorption'

14.4V / 28.8V (adjustable)

Charge voltage 'float'

13.8V / 27.6V (adjustable)

Charge voltage 'equalization' 

3

16.2V / 28.8V (adjustable)

Temperature compensation

12V: -16mV/°C / 24V: -32mV/°C

Protection

Output short circuit, over temperature

Operating temperature

-30°C to +60°C (full rated output up to 40°C)

Humidity

95%, non-condensing

Maximum altitude

5000m (full rated output up to 2000m)

Environmental condition

Indoor type 1, unconditioned

Pollution degree

PD3

Data communication

VE.Direct port 

4

ENCLOSURE

Colour

Blue (RAL 5012)

Power terminals

16 mm² / AWG6

Protection category

IP43 (electronic components), IP22 (connection area)

Weight

1.3 kg

Dimensions  h x w x d

130 x 186 x 70 mm

STANDARDS

Safety

EN/IEC 62109-1, UL 1741, CSA C22.2

1a) The solar charger will limit input power if more PV power is connected.

1b) The PV voltage must exceed Vbat + 5V for the controller to start. Thereafter the minimum PV voltage is Vbat + 1V.

2) A higher short circuit current may damage the solar charger in case of reverse polarity connection of the PV array.

3) Equalization is by default disabled.

4) For more information on data communication see the 

data communication paper

 in the 

Technical information section

 on

our website.

MPPT solar charger manual

Page 52

Technical specifications

Summary of Contents for BlueSolar 100/30






























































Reviews:

No comments

Brands by name

Popular brands

Load more brands