background image

 

UG:118 

vicorpower.com  

Applications Engineering: 800 927.9474 

Page 2

Set Up

The Customer Evaluation Board should be set up as follows:

Note: 

Care should be taken to avoid reversing polarities if connecting to the opposite

(solder) side of the board.

+IN, –IN

Connect a high-quality, low noise power supply to the +IN and-IN terminals of the 
Customer Evaluation Board. The startup slew rate of the input source should be no 
greater than 1 V/µs. The interconnect leads should be heavy gauge and as short as 
possible. Additional capacitance may have to be added on the evaluation board to 
make up for impedances in the interconnect leads as well as deficiencies in the source. 

+OUT, –OUT

The load should be connected to +OUT and –OUT terminals of the evaluation board 
with short leads of suitable gauge to carry the output current and minimize losses. The 
evaluation board can be connected directly to the application for which the module is 
intended. However the interconnect impedances between the evaluation board and the 
application can greatly affect the transient response. For applications where transient 
response is critical, the user should consider mounting the HDC module directly to 
the target application PCB. Test points TP14 (+OUT) and TP06 (-OUT) can be used to 
monitor the output.

Primary Control (PC)

The PC can be used to disable the HDC or provide a primary referenced bias supply. The 
module can be disabled by connecting PC (TP03) to –HDC_IN (TP05).

Trim (TR)

The S01 switch on the Customer Evaluation Board can be used to enable or disable 
output voltage trimming on the HDC. Potentiometer R12 can be adjusted to trim the 
output voltage of the converter.

Figure 1.

HDC Customer Evaluation Board 

layout drawing, component side

Summary of Contents for HD Series







Reviews: