Vicon Roughneck V920D Series Instruction Manual Download Page 31

Reference

 

 

Coaxial Cable Recommendations

 

 

Caution: 

Careful  selection  of  proper  cable  is  essential  to  obtain  the  best  performance  from  this  equipment.  Vicon  assumes  no

 

responsibility for poor performance when cables other than those recommended, or equivalent, are installed. In all cases, coaxial cable

 

impedance should be 75 ohms.

 

 

Materials

 

Use  only  a  pure  copper  center  conductor.  Do  not  use  a  copper-plated  steel  or  aluminum  center  conductor,  as  they  will

 

result  in  poor  quality  video.  Solid-core  bare  copper  conductor  is  the  best  type,  where  flexing  and  bending  will  be  minimal.

 

If  severe  bending  and  flexing  is  required  for  installation,  use  a  stranded  center  conductor.  Never  exceed  the

 

manufacturer’s  minimum  bend  radius  specification.  Use  cellular  (foam)  polyethylene  dielectric  except  where  heavy

 

moisture  exists.  For  moisture  conditions,  use  solid  polyethylene  dielectric  cable  with  a  heavy  exterior  insulation.  The

 

shield must be copper braid providing 95% or better coverage.

 

 

Cable  Types

 

The  cable  types  listed  below  are  the  most  common  75-ohm  types  used.  They  vary  in  size  (diameter),  dielectric  type  and

 

net  DC  resistance.  The  larger  cable  results  in  a  lower  DC  resistance  and  better  video  quality,  with  increased  difficulty  in

 

handling  and  installation.  Let  the  required  picture  quality  and  cable  distance  provide  a  guide  in  choosing  the  best  cable

 

type. For cables  other than  the approved Vicon  types below, contact the manufacturers listed below. Note that 

“BC” refers

 

to bare copper and 

“TC” refers to tinned copper.

 

 

Recommended  Coaxial  Cable  Types

 

Cable

 

Type

 

Belden

 

Type No.

 

Alpha

 

Type No.

 

West Penn

 

Type No.

 

Type Center

 

Conductor

 

Type Shield and

 

% Coverage

 

DC Resistance

 

ohms/1000 ft (km)

 

RG-11/U

 

8213

 

9847

 

811,4811

 

14 Solid BC

 

BC braid (95%)

 

2.6 (8.5)

 

RG-6/U

 

9248

 

9804C

 

806,4806

 

18 Solid BC

 

Foil + 61% TC braid (100%)

 

7.5 (24.6)

 

RG-59/U

 

8281*

 

----

 

815

 

20 Solid BC

 

2 TC braids (96%)

 

9.9 (32.5)

 

RG-59/U

 

9259

 

9803

 

816

 

22 Stranded BC

 

BC braid (95%)

 

15.0 (49)

 

RG-59/U

 

9659

 

----

 

----

 

22 Stranded BC

 

BC braid (95%)

 

15.0 (49)

 

*Requires special BNC-M connector due to 0.305 nominal O.D.

 

Belden Inc.

 

http://www.belden.com/

 

(800) 235-3361

 

Alpha Wire Company

 

http://www.alphawire.com/

 

(800)-52 ALPHA (522-5742)

 

 

Picture Quality vs.  Cable  Length

 

Picture  Quality

 

Maximum Cable  Run** ft (m)

 

RG-59/U

 

RG-6/U

 

RG-11/U

 

Usable  picture

 

1100  (350)

 

1500  (450)

 

2400  (750)

 

Clean  picture

 

820 (250)

 

1000  (300)

 

1600  (500)

 

Best  picture

 

400 (120)

 

530  (160)

 

820 (250)

 

** For longer cable runs, use a Vicon Video Amplifier to obtain a suitable  picture.

 

 
 
 
 
 
 
 
 
 
 
 
 

 

 

                                                                                                                                                                             Reference 31

 

 

 

 

 

 

 

West Penn Wire

 

http://www.westpenn-cdt.com/

 

(800)-245-4964

 

 

Summary of Contents for Roughneck V920D Series




































Reviews: