background image

XX018 Rev 200 NOVA V1400X-HSB-M

Shipping Instructions  

  19

Shipping Instructions

Use the following procedure when returning a unit to the factory:

1.  Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name

of the Vicon employee who issued the R.A.

Vicon Industries Inc.
89 Arkay Drive
Hauppauge, NY  11788
Phone: 631-952-CCTV; Toll-Free: 1-800-645-9116; Fax: 631-951-CCTV

For service or returns from countries in Europe, contact:

Vicon Industries (U.K.) Ltd
Brunel Way
Fareham, PO15 5TX
United Kingdom
Phone: 44/(0)1489/566300; Fax: 44/(0)1489/566322

2. 

Attach a sheet of paper to the unit with the following information:

a. 

Name and address of the company returning the unit

b. 

Name of the Vicon employee who issued the R.A.

c. 

R. A. number

d. 

Brief description of the installation

e. 

Complete description of the problem and circumstances under which it occurs

f. 

Unit’s original date of purchase, if still under warranty

3.  Pack the unit carefully. Use the original shipping carton or its equivalent for maximum protection.

4.  Mark the R.A. number on the outside of the carton on the shipping label.

Summary of Contents for NOVA V1400X-HSB-M





























Reviews: