manualshive.com logo in svg

Viavi CellAdvisor 5G, User Manual

The Viavi CellAdvisor 5G is an advanced network testing tool designed to ensure seamless connectivity in the era of 5G technology. For quick and easy access to all its features, refer to our comprehensive user manual available for free download on our website.

Share
Download
background image

CellAdvisor 5G User's Guide 

313 

Transmitter off to on power with 5G TM 

 

Transmitter on to off power with 5G TM 

 

  

Conducting signal quality 

 

Modulation quality 

Modulation quality is defined by the difference between the measured carrier signal and an ideal signal. Modulation quality can be 
expressed as Error Vector Magnitude (EVM). The Error Vector Magnitude is a measure of the difference between the ideal symbols 
and the measured symbols after the equalization. This difference is called the error vector. OTA modulation quality is defined by the 
difference between the measured carrier signal and an ideal signal. Modulation quality can e.g. be expressed as Error Vector 
Magnitude (EVM). The Error Vector Magnitude is a measure of the difference between the ideal symbols and the measured symbols 
after the equalization. This difference is called the error vector. OTA modulation quality requirement is defined as a directional 
requirement at the RIB and shall be met within the OTA coverage range. 

Summary of Contents for CellAdvisor 5G








































































































































































































































































































































































Reviews:

No comments

Related manuals for CellAdvisor 5G

Badger Meter HR-LCD 4-20 User Manual preview
HR-LCD 4-20
Brand: Badger Meter Pages: 12
Badger Meter ER-9 User Manual preview
ER-9
Brand: Badger Meter Pages: 16
Badger Meter M-series Installation And Operation Manual preview
M-series
Brand: Badger Meter Pages: 56
Badger Meter ModMAG M Series Installation Manual preview
ModMAG M Series
Brand: Badger Meter Pages: 4
IET Labs 1910 User And Service Manual preview
1910
Brand: IET Labs Pages: 114
Gardner Bender GCM-221 Operating Instructions Manual preview
GCM-221
Brand: Gardner Bender Pages: 7
Keller CellaCast PA8 Series Quick Manual preview
CellaCast PA8 Series
Brand: Keller Pages: 12
BYOGuitar.com JEM Assembly Instructions Manual preview
JEM
Brand: BYOGuitar.com Pages: 11
Siko IKM360R Quick Start Manual preview
IKM360R
Brand: Siko Pages: 2
Primes Cube L1 Original Instructions Manual preview
Cube L1
Brand: Primes Pages: 56
Oakton WD-35606-00, WD-35606-05 Operating Instructions Manual preview
WD-35606-00, WD-35606-05
Brand: Oakton Pages: 10
Fuji Electric ZRE-2 Instruction Manual preview
ZRE-2
Brand: Fuji Electric Pages: 85
Industrial Scientific iTrans 77023554 Manual preview
iTrans 77023554
Brand: Industrial Scientific Pages: 94
mru NOVAplus biogas User Manual preview
NOVAplus biogas
Brand: mru Pages: 78
VOLTCRAFT LWT-04 Operating Instructions Manual preview
LWT-04
Brand: VOLTCRAFT Pages: 8
Megasat Digital 1 User Manual preview
Digital 1
Brand: Megasat Pages: 25
Thermocable ProH2O Application Manual preview
ProH2O
Brand: Thermocable Pages: 10
Bartington Mag-01H Operation Manual preview
Mag-01H
Brand: Bartington Pages: 32

Brands by name

Popular brands

Load more brands