manualshive.com logo in svg

Viavi CellAdvisor 5G, User Manual, Page: 292 / 359

Share
Download
Viavi CellAdvisor 5G User Manual Download Page 292

Using DSS Signal Analyzer 

280 

Signal Power 

Primary 
Synchronization 
Signal power 

P-SS 
Power 

Test limits On/Off, High Limit/Low Limit 

Note that based on the 

Reference  Mode

 you have chosen from 

Menu

 > 

Reference Mode

 between 

Absolute

 and 

Relative

, you can set the first high/low limit when you chose absolute, and second 

high/low limit when you chose relative. 

Secondary 
Synchronization 
Signal power 

S-SS 
Power 

Test limits On/Off, High Limit/Low Limit 

Note that based on the 

Reference  Mode

 you have chosen from 

Menu

 > 

Reference Mode

 between 

Absolute

 and 

Relative

, you can set the first high/low limit when you chose absolute, and second 

high/low limit when you chose relative. 

Physical 
Broadcast 
Channel Power 

PBCH 
Power 

Test limits On/Off, High Limit/Low Limit 

Note that based on the 

Reference  Mode

 you have chosen from 

Menu

 > 

Reference Mode

 between 

Absolute

 and 

Relative

, you can set the first high/low limit when you chose absolute, and second 

high/low limit when you chose relative. 

Frame Average 
Power 

Frame Avg 
Power 

Test limits On/Off, High Limit/Low Limit 

OFDM Symbol 
Power 

OFDM 
Symbol 
Power 

Test limits On/Off, High Limit/Low Limit 

Magnitude of 
the carrier 
feedthrough 
signal

 

IQ Origin 
Offset 

Test limits On/Off, High Limit 

4

      

Optional.

 Tap the 

Save

 icon on the side bar and select the save option form the choices available for your measurement mode. 

Frame measurement with DSS Analyzer 

 

  

 

Time alignment error 

In eNode-B supporting Tx Diversity transmission, signals are transmitted from two or more antennas. These signals shall be aligned. 
The time alignment error in Tx diversity is specified as the delay between the signals from two antennas at the antenna ports. 

Summary of Contents for CellAdvisor 5G








































































































































































































































































































































































Reviews:

No comments