Viavi 87339 Operation Manual Download Page 104

Page: 104 / 198

Testing

5 -5

5.2.4

Identifying Installed Software Version

Perform the following steps to identify the software version installed in the GPSG-1000.

STEP

PROCEDURE

14.

Press the Power On button to turn the test set on.

15.

Allow the test set to complete the boot process, approximately 5.5 mins.

16.

Open the Launch Bar by touching the light gray bar located on the left side of the

User Interface and scroll down to the System function key.

STEP

PROCEDURE

17.

Touch the System function key to open the System sub-menu and select System

Update.

18.

In the Version window the unit serial number and currently installed software

version number is displayed. In the following example, “1000372866” is the unit

serial number, and “2.0.0,201111221441” is the currently installed software

version number.

Summary of Contents for 87339







































































































































































































Search results

Summary of Contents for 87339

Reviews:

Brands by name

Popular brands

Viavi 87339, Operation Manual

Search results

Summary of Contents for 87339

Reviews:

Brands by name

Popular brands