VIASYS Bear Cub 750PSV Service Manual Download Page 95 | Manualshive

Page: 95 / 98

VIASYS Bear Cub 750PSV Service Manual Download Page 95

Service Manual

95

Chapter 11 Repackaging Instructions

General

The packaging system for the BEAR CUB™ 750PSV Infant Ventilator has been
designed to provide a high degree of protection against shipping damage.

All shipments of BEAR CUB™ 750PSV Infant Ventilators should be made using the
complete packaging system.

Allied Healthcare Products, Inc., does not assume any liability whatsoever for any
damage incurred in any product returned to our facilities by any means. The shipper
and carrier are totally responsible for all damage and costs involved in transporting
returned goods. If a package is damaged in shipment, your shipper and/or carrier
should be notified within ten days of receipt of the shipment.

Packaging Instructions

NOTE

It is advisable that a shipping department or organization perform this procedure. A
local freight company will usually pack the product at your facility for a small service
charge.

The packaging carton consists of:

Accessory Carton

51000-09505

Anti-static Bag 26"x22"x44"

51000-06056

Cavity pack-bottom

51-09504-02

Cavity pack-top

51-09504-01

Shipping Carton

51000-09502

Shipping Label

51000-20038

Procedure

Refer to Figure 11-1 when following this procedure.

1.

Place a large plastic bag over the ventilator.

2.

Attach a shipper to the plastic bag with tape.

3.

Place the accessory carton inside the shipping carton.

4.

Align the bottom portion of cavity-pack so it slides in place inside the carton.

5.

Place the ventilator in the carton, align the ventilator so it slides into the cavity-
pack bottom.

6.

Align the top portion of the cavity-pack on top of the ventilator.

7.

Seal the box top flaps with heavy duty packaging tape.

L2346

Revision B

June 2004

«
...
93
94
95
96
97
...
»

Summary of Contents for Bear Cub 750PSV



































































































Reviews:

No comments