VIASYS Bear Cub 750PSV Service Manual Download Page 21

Page: 21 / 98

Service Manual

Ventilator Dimensions

13.5" W x 10" D x 11" H

Graphics Display Dimensions

13" W x 2.5" D x 9.5" H

Pedestal Stand Dimensions

24" x 40.5" H

Compressor Dimensions

22"W x 21.5"D x 36" H

Shipping Weight Including Ventilator

38 lbs.

Graphics Display

11 lbs.

Pedestal Stand

12 lbs.

Compressor 122

lbs.

Shipping Dimensions

Ventilator

18" W x 18" D x 19" H

Graphics Display

16" W x 13" D x 11" H

Pedestal Stand

25" W x 5" D x 45" H

Compressor

26" W x 22" D x 40" H

Environmental Specifications

Temperature

Storage and Shipping

-40 to 158 ºF (-40 to 70 ºC)

Checkout and Operating

50 to 104 ºF (10 to 40 ºC)

Altitude

Checkout, Operating,
Transport and Storage

0 to 9,000 feet (14.7 to 10.5 PSIA/760 to 543 mm Hg)

Humidity

Storage and Shipping

0 to 99% Relative Humidity — Non-condensing

Checkout and Operating

0 to 95% Relative Humidity — Non-condensing

Method of Sterilization/Disinfection

NOTE

See also the BEAR CUB™ 750PSV Infant Ventilator Instruction Manual Cleaning
and Maintenance (chapter 8)

L2346

Revision B

June 2004

Summary of Contents for Bear Cub 750PSV


































































































Search results

Summary of Contents for Bear Cub 750PSV

Reviews:

VIASYS Bear Cub 750PSV, Service Manual, Page: 21 / 98

Search results

Summary of Contents for Bear Cub 750PSV

Reviews: