manualshive.com logo in svg

VIA Technologies EPIA-M920, User Manual, Page: 81 / 93

Share
Download
VIA Technologies EPIA-M920 User Manual Download Page 81

VIA EPIA-M920 User Manual 

70

 

7.

 

Software and Technical Support 

7.1.

 

Microsoft and Linux Support 

The VIA EPIA-M920 is compatible with Microsoft Windows and Linux operating systems. 

7.1.1.

 

Driver Installation 

Microsoft Driver Support 

The latest windows drivers can be downloaded from the VIA website at 

www.viatech.com

. 

Linux Driver Support 

Linux drivers are provided through various methods including: 

 

Drivers provided by VIA (binary only). An ARCM or NDA/BSLA may be asked in order to get the 
drivers, please contact our sales representative to submit a request. 

 

Using a driver built into a distribution package 

 

Installing a third party driver (such as the ALSA driver from the Advanced Linux Sound Architecture 
project for integrated audio) 

7.2.

 

Technical Support and Assistance 

•

 

For utilities downloads, latest documentation and information about the VIA EPIA-M920, please 
visit our website at 

http://www.viatech.com/en/boards/mini-itx/epia-m920

 

•

 

For technical support and additional assistance, always contact your local sales representative or 
board distributor, or go to 

https://www.viatech.com/en/support/technical-support

 for technical 

support. 

•

 

For OEM clients and system integrators developing a product for long term production, other 
code and resources may also be made available. Please visit our website at 

https://www.viatech.com/en/about/contact

 to submit a request. 

 

Summary of Contents for EPIA-M920






























































































Reviews:

No comments