VZ-TVI-B2040VF
HD1080P Vari-focal IR
Bullet Camera
User Manual
Regulatory Information
FCC Information
FCC compliance:
This equipment has been tested
and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide
reasonable
protection against harmful
interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio
frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio
communications. Operation
of this equipment in a residential area is likely to
cause harmful
interference in which case the user
will be required to correct the interference at his
own expense.
FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1.
This device may not cause harmful
interference.
2.
This device must accept any interference
received, including interference that may
cause undesired operation
.
EU Conformity Statement
1
Introduction
1.1
Product Features
This series of camera adopts new generation
sensor with high sensitivity and advanced circuit
design technology
.
It features high resolution, low
image distortion and low noise, etc
.
, which
makes it suitable for surveillance system and
image processing system
.
•
High performance CMOS sensor and high
resolution bring high-quality image;
•
Low illumination;
•
OSD menu, parameters are configurable;
•
Support auto white balance, auto gain control,
electronic shutter control;
•
Support image effect adjustment;
•
Unit transmission control;
•
Advanced 3-axis design meets different
installation requirements.
Cameras in some models do not support OSD
menu. For actual operation, please refer to the
specification of each model.
1.2
Overview
1.2.1 Overview of Type I Camera
2
Installation
Before you start
:
•
Please make sure that the device in the package is
in good condition and all the assembly parts are
included.
•
Make sure that all the related equipment is
power-off during the installation.
•
Check the specification of the products for the
installation environment.
•
Check whether the power supply is matched
with your power output to avoid damage.
•
Please make sure the wall is strong enough to
withstand three times the weight of the camera
and the mounting.
•
If the wall is the cement wall, you need to insert
expansion screws before you install the camera.
If the wall is the wooden wall, you can use
self-tapping screw to secure the camera.
•
If the product does not function properly,
please contact your dealer or the nearest
service center. Do not disassemble the camera
for repair or maintenance by yourself.
2.1
Installation of Type I Camera
Steps:
1.
Drill the screw holes and the cable hole on the
ceiling according to the supplied drill template.
Thank you for purchasing our product. If there
are any questions, or requests, please do not
hesitate to contact the dealer.
This manual may contain several technical
incorrect places or printing errors, and the
content is subject to change without notice. The
updates will be added to the new version of this
manual. We will readily improve or update the
products or procedures described in the manual.
This product and - if applicable - the
supplied accessories too are marked
with "CE" and comply therefore with
the applicable harmonized European
standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC
,
the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
Figure 2-1 The Drill Template
Privacy Notice
Surveillance laws vary by jurisdiction. Check
all
relevant laws in your jurisdiction before using this
product for surveillance purposes to ensure that
your use of this product conforms.
Please refer to the product specification for
camera parameters and functions.
www.vezcocctv.com
municipal waste in the European
Union. For proper recycling, return
this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more
information see:
2006/66/EC (battery directive):
This product contains a battery that
cannot be disposed of as unsorted
municipal waste in the European
Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your
supplier or to a designated collection point. For
more information see: www.recyclethis.info.
Figure 1-1 Overview of Type I Camera
1.2.2 Overview of Type
II
Camera
Figure 1-2 Overview of Type II Camera
2.
Push the lock button to disassemble the camera
from the mounting base.
Figure 2-2 Release the Lock Screw
3.Fix the mounting base to the ceiling.
4.
Route the cables to the cable hole and connect
the corresponding cables.
5.
Secure the camera to the mounting base by
supplied screws. Keep the word UP on the camera
being upright during the installation to make the
image showing normally.
