Vetus DT4.70 Operation Manual Download

Page: 110 / 144

108

1 Engine will not crank

Possible fault

Remedy

Faulty or discharged battery
(too low voltage ).

Check / recharge battery and
check engine alternator and/or
battery charger.

Fuse blown.

Replace.

Loose or corroded connec-
tions in starting circuit.

Clean and tighten connections.

Wrong engine electric mass
connection.

Repair.

Faulty starter-switch or faulty
starter-relay.

Check / replace.

Faulty starter-motor or pinion
does not engage.

Check / replace starter-motor.

Seized components.

Repair.

Water in the cylinder .

Check / Repair.

2 Engine cranks but will not start, no smoke from exhaust

Possible fault

Remedy

(Nearly) Empty fuel tank.

Refill.

Fuel stop valve closed.

Open.

Fuel pre-filter clogged .

Clean /replace

Fuel filter clogged with water
and/or contamination.

Check or replace.

Vent line of fuel supply tank
clogged.

Check / clean.

Faulty injector/injection pump.. Check, replace if required.
Fuel electric pressure regula-
tor clogged

Check /clean or replace

Leaking fuel supply line or fuel
injection line.

Check / replace.

Air in fuel system.

Check and bleed.

Electrical fuel low pressure
pump is not working.

Check the electrical connection,
check the pump, replace.

Exhaust restricted.

Check.

9 Troubleshooting

Fault finding table

Summary of Contents for DT4.70

















































































































































Search results

Summary of Contents for DT4.70

Reviews:

Related manuals for DT4.70

Brands by name

Popular brands

Vetus DT4.70, Operation Manual

Search results

Summary of Contents for DT4.70

Reviews:

Related manuals for DT4.70

Brands by name

Popular brands