Vetter ManuTel SlimLine Operating Instructions Manual Download

Page: 3 / 43

This operating manual (hereinafter also referred to as “manual”) contains basic informa-

tion that is to be observed during the assembly, operation and maintenance of the
VETTER Manu

Tel

Slim

Line

telescopic

fork arms

(hereinafter referred to as Manu

Tel

Slim

Line

). It is therefore imperative that this manual be read prior to all work on and with

the fork arms. Ensure that the manual is always available at the operation site of the
Manu

Tel

(on the industrial truck).

Illustrations in this manual are for basic understanding and may deviate from the actual

design.

Address

VETTER Industrie GmbH

Carl-Benz-Strasse 45

57299 Burbach

GERMANY

Phone

+49 2736 4961–0

[email protected]

Internet

www.forks.com

About this

operating

manual

Customer

service

Supplemental directives

V1.09/2019

ManuTel

telescopic fork arm Type SlimLine

Summary of Contents for ManuTel SlimLine












































Search results

Summary of Contents for ManuTel SlimLine

Reviews:

Related manuals for ManuTel SlimLine

Brands by name

Popular brands

Vetter ManuTel SlimLine, Operating Instructions Manual

Search results

Summary of Contents for ManuTel SlimLine

Reviews:

Related manuals for ManuTel SlimLine

Brands by name

Popular brands