Vestil WTJ-HITCH Instruction Manual Download Page 4

Table of Contents

 

Rev. 6/21/2019 

WTJ-HITCH MANUAL 

Table of Contents

 

Copyright 2019 Vestil Manufacturing Co. 

Page 

4

 of 

9

 

 

 

 

Exploded View & Bill of Materials

 

 

 

      

 

 

 

 

 

 

 

 

Item   Part no. 

Description 

Qty.  Item   Part no. 

Description 

Qty. 

28-514-251  Assembly, base frame 

16 

99-612-003  Assembly, hitch pin and pin clip 

28-514-252  Assembly, boom 

17 

13105 

3

/

8

” -16 x 1” HHCS #5 z-plated bolt 

28-516-065  Assembly, bracket, hitch collar 

18 

13211 

1

/

2

” – 13 x 2” HHCS #5 z-plated bolt 

28-516-066  Assembly, bracket hitch tube 

19 

13217 

1

/

2

” – 13 x 3

1

/

2

” HHCS #5 z-plated bolt 

28-516-067  Assembly, bracket, post 

20 

13363 

3

/

4

” – 10 x 2

1

/

2

” HHCS #5 z-plated bolt 

08-145-037  1-ton clevis hook 

21 

13371 

3

/

4

” – 10 x 4

1

/

2

” HHCS #5 bolt 

21-042-002-001 

Hand winch, foldable handle grip 

22 

17945 

3

/

4

” – 16 x 8

1

/

2

” yellow zinc grade 8 bolt 

99-145-067  Compression sleeve, 

3

/

16

” x 1” 

23 

33008 

3

/

8

” USS flat washer z-plated 

21-145-013  Thimbles, LLW 

24 

33018 

3

/

4

” USS flat washer z-plated 

10 

28-014-380  Frame, boom brace 

25 

33622 

3

/

8

” lock washer z-plated 

11 

28-016-213  Bracket, threaded hitch stiffener 

26 

36106 

3

/

8

” – 16 hex nut z-plated 

12 

28-027-010  Roller 

27 

36110 

1

/

2

” – 13 hex nut z-plated 

13 

33-112-034  Clevis pin, 

3

/

4

” x 3

3

/

4

” long 

28 

36466 

3

/

4

” – 16 yellow zinc grade 8 hex nut 

14 

42-145-004 

3

/

16

” aircraft cable, 180” long 

29 

37039 

3

/

4

” – 10 nylock nut z-plated 

15 

99-027-003 

1

/

4

” cable pulley, 3” OD, 

1

/

2

” ID 

30 

45282 

#6 hitch pin clip 

 

 

 

 

31 

48593 

1

/

2

” – 13 x 1

5

/

8

” channel nut  

 

Tools needed for assembly: 

1

1

/

in. wrenches (for 20, 21, 22 & 28) 

9

/

16 

in. wrenches (for 17 & 26) 

3

/

4

in. wrenches (for 18, 19, 27, & 31) 

 

Summary of Contents for WTJ-HITCH










Reviews: