Vestil SWA-48, Instruction Manual

Page: 4 / 17

Table of Contents 9/9/2021 SWA-48-PMO MANUAL
Table of Contents Copyright 2019 Vestil Manufacturing Corp.; All rights reserved Page 4 of 17
Machine Installation: Numbers in parentheses () correspond to item numbers in the Exploded View on p. 8.
1. Move the machine to its installation location with a fork truck. Insert the forks lengthwise along each side of the
frame. Adjust fork spacing (on the forklift carriage) so that the forks lie underneath the ½” x 3” x 3” anchoring tabs
on each side of the frame. Be careful to avoid damaging the electrical components.
2. Prop up the motor end of the frame (1), for instance with 4” x 4” lumber or something similar.
3. Stand the mast (18) upright on the end of the frame opposite the turntable. Standing at the end of the frame
opposite the turntable, the mast must be oriented with the (stretch wrap) carriage on the left side of the frame.
Align the hole in each corner of the mast mounting plate with its corresponding hole in the frame.
4. Bolt the mast to the frame with the hardware provided, and wrench-tighten.
5. Remove the counterbalance retaining screw. The screw is located approximately 12” up from the bottom of the
mast. Cut the cable tie holding the mast cable to the pulley at the top of the mast.
6. Anchor the frame to the floor. There are 9/16” holes located at the corners of the frame and under the edge of the
turntable. Tighten the anchors until the frame is level.
7. Shim and/or apply grout under the frame wherever the frame is not in contact with the ground to prevent bowing.
8. Tighten all of the anchor bolts with an appropriately sized wrench.
9. Bolt the motor & drive assembly (15) onto the gear reducer using the included hardware and shaft key. When
finished, the drive controller should face the right side of the frame.
10. Connect the (turntable) power cord plug to a standard 15A or 20A, 120 VAC receptacles. If a powered mast (see
p. 18) is installed, the turntable power cord can plug into the pigtail cord from the mast’s control enclosure. Plug the
mast’s power cord into a 120V receptacle to supply both the mast and turntable with electricity.
11. Verify that the turntable rotates and that the speed control knob provides full speed range adjustment. If a
powered mast is installed, verify that the mast operates (see Operating the Powered Mast on p. 12) and that the
mast's upper and lower travel limit switches function properly.
12. Clean up debris. Confirm that all labels are intact and easily readable. See Labeling diagram on p. 12.
Stretch Wrap Holder Assembly
The wrap holder accommodates 10-20 inch rolls of stretch wrap.
Loading stretch wrap:
1. Unwind the wing nut (A) sufficiently to remove the lock spacer (6)
underneath the bottom retainer (2).
2. Remove the lock spacer.
3. Remove the retainer (5) and bearing (4).
4. Remove the spent roll of stretch wrap and install a new roll.
5. Reinstall the retainer (5); secure it in place with the lock spacer (6).
6. Tighten the wing nut (A) until the roll is snugly grasped between the
tube retainers (2) and (3). Adjust the tightness of the wing nut to
achieve the desired degree of material stretch—the material will
stretch more the more tightly the roll is grasped.
Item Part no. Description Qty.
1 20-014-116 Frame, rod, wrap retainer 1
2 20-014-006 Tube retainer (bottom) 1
3 20-014-005 Tube retainer (top) 1
4 20-110-002 Bearing, ball,
3
/
4
in., shield 1
5 68061 1
5
/
8
in. retainer ring 1
6 20-113-022 Spacer, lock 1
7 20-113-003
7
/
8
in. fiber washer 1
*8 SRF-18 20in. plastic wrap (not included) 1
8