background image

Operator’s Manual  

2/2/21  

EHLT, MANUAL.DOCX 

 

Table of Contents

  

Copyright 2020, Vestil Manufacturing Corp. 

Page 

24

 of 

24

 

LIMITED WARRANTY 

Vestil Manufacturing Corporation (“Vestil”) warrants this product to be free of defects in material and workmanship during the 

warranty period. Our warranty obligation is to provide a replacement for a defective, original part covered by the warranty after we 
receive a proper request from the Warrantee (you) for warranty service. 

Who may request service? 

Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an authorized 

distributor AND Vestil has been fully paid. 

Definition of “original part”? 

An original part is a part used to make the product as shipped to the Warrantee. 

What is a “proper request”? 

A request for warranty service is proper if Vestil receives: 1) a photocopy of the Customer Invoice that displays the shipping 

date; AND 2) a written request for warranty service including your name and phone number. Send requests by one of the following 
methods: 
US Mail 
Vestil Manufacturing Corporation 
2999 North Wayne Street, PO Box 507 
Angola, IN 46703 

Fax 

(260) 665-1339 

Phone 

(260) 665-7586 

Email 

[email protected] 

Enter “Warranty service request” in subject field 

In the written request, list the parts believed to be defective and include the address where replacements should be delivered. 

After Vestil receives your request for warranty service, an authorized representative will contact you to determine whether your 
claim is covered by the warranty. Before providing warranty service, Vestil will require you to send the entire product, or just the 
defective part (or parts), to its facility in Angola, IN. 

What is covered under the warranty? 

The warranty covers defects in the following original, dynamic parts: motors, hydraulic pumps, motor controllers, and cylinders. 

It also covers defects in original parts that wear under normal usage conditions (“wearing parts”), such as bearings, hoses, wheels, 
seals, brushes, and batteries. 

How long is the warranty period? 

The warranty period for original dynamic components is 1 year. For wearing parts, the warranty period is 90 days. Both 

warranty periods begin on the date Vestil ships the product to the Warrantee. If the product was purchased from an authorized 
distributor, the periods begin when the distributor ships the product. Vestil may, at its sole discretion, extend a warranty period for 
products shipped from authorized distributors by up to 30 days to account for shipping time. 

If a defective part is covered by the warranty, what will Vestil do to correct the problem? 

Vestil will provide an appropriate replacement for any covered part. An authorized representative of Vestil will contact you to 

discuss your claim. 

What is not covered by the warranty? 

The Warrantee (you) are responsible for paying labor costs and freight costs to return the product to Vestil for warranty service. 

Events that automatically void this Limited Warranty. 

 

Misuse; 

 

Negligent assembly, installation, operation or repair; 

 

Installation/use in corrosive environments; 

 

Inadequate or improper maintenance; 

 

Damage sustained during shipping; 

 

Collisions or other accidents that damage the product; 

 

Unapproved modifications: Do not modify the product IN ANY WAY without first receiving written authorization from Vestil. 

Do any other warranties apply to the product? 

Vestil Manufacturing Corp. makes no other express warranties. All implied warranties are disclaimed to the extent allowed by 

law. Any implied warranty not disclaimed is limited in scope to the terms of this Limited Warranty. Vestil makes no warranty or 
representation that this product complies with any state or local design, performance, or safety code or standard. Noncompliance 
with any such code or standard is not a defect in material or workmanship. 

 

 

Summary of Contents for EHLT Series

























Reviews: