background image

Operator’s Manual 

4/16/21  

CTD-H-TP-3000 MANUAL.DOCX 

 

Table of Contents

  

Copyright 2021, Vestil Manufacturing Corp. 

Page 

1

 of 

14

 

 

Vestil Manufacturing Corp.

 

A company dedicated to solving loading dock and material handling 

problems since 1955. 

2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 

Telephone: (260) 665-7586 -or- Toll Free: (800) 348-0868 

Fax: (260) 665-1339 

http://www.vestil.com/   email: [email protected] 

CTD-H-TP-3000 Hydraulic Crate Dumper 

Instruction Manual

 

  

 
Receiving instructions: 

After delivery, remove the packaging from the product. Inspect the product to determine whether it sustained 

damage during transport. If damage is discovered, record a complete description of it on the bill of lading and file a claim 
with the carrier immediately! If the product is undamaged, discard the packaging. 
NOTE: 

The end user is solely responsible for confirming that product design, use, and maintenance comply with laws, 

regulations, codes, and mandatory standards applied where the product is used. 
Replacement Parts and Technical Assistance: 

If you have questions that are not addressed in these instructions, or to order replacement parts, labels, and 

accessories, call (260) 665-7586 and ask for the Service and Parts Department. You can also reach Service and Parts 
online at 

https://www.vestil.com/page-parts-request.php

. 

Electronic Copies of Instruction Manuals: 
  Additional copies of this instruction manual may be downloaded from https://www.vestil.com/page-manuals.php. 

 

 

Summary of Contents for CTD-H-TP-3000















Reviews: