Vestil BBL-4 Use And Maintenance Manual Download Page 3

Table of Contents

 

Rev. 5/8/2019 

BBL-4 MANUAL 

Table of Contents

 

Copyright 2019 Vestil Manufacturing Co. 

Page 3 of 6 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SIGNAL WORDS  

This manual classifies personal injury risks and situations that might cause property damage with signal words. 

Signal words indicate the seriousness of injuries that might result if a particular act does, or does not, occur. 

 

Identifies a hazardous situation which, if not avoided, WILL result in DEATH or SERIOUS 

INJURY.  Use of this signal word is limited to the most extreme situations. 
Identifies a hazardous situation which, if not avoided, COULD result in DEATH or SERIOUS 

INJURY. 
Indicates a hazardous situation which, if not avoided, COULD result in MINOR or 

MODERATE injury. 

 

 

Identifies practices likely to result in product/property damage, such as operation that might 

damage the product. 

 

 

 

 

 

 

 

 

 

HAZARDS 

Vestil strives to identify all foreseeable hazards associated with the use of its products. However, no manual can 

address every possible risk. The most effective means for avoiding injury is to read all of the instructions prior to 

putting the dumper into service and to  apply sound judgment whenever using this device. 

 

 

 

  Improper or careless use of this product might result in serious personal injuries. 

 

Read and understand  the entire manual before installing, using,  or servicing the product

. Read the manual 

whenever necessary to refresh your understanding of proper use and maintenance procedures. 

  Review the safety messages included in the manuals of devices used with this bulk bag lifter, e.g. crane, trolley, 

hoist, forklift, or forklift attachment. 

  ALWAYS inspect the lifter before each use according to the inspection procedures described in the most recent 

revision of 

ASME B30.20

  “Below-the-Hook Lifting Devices”.  B30.20 also describes inspections that should be 

performed frequently and periodically inspections. Conduct these inspections as detailed in the standard and with 

the recommended frequency. 

  Properly maintain the lifter according to the 

Inspections & Maintenance

 procedures on p. 4 of this manual.  These 

procedures to 

supplement

 the inspection and maintenance recommendations in ASME B30.20. 

  ALWAYS attach the lifter to a safety hook, i.e. a hook with a self-closing latch, to prevent accidental detachment 

from the hook.  DO NOT connect the lifter to a damaged or malfunctioning safety hook. 

  Make sure that the travel path is clear. 

  DO NOT remove or obscure any label. Before using the lifter, confirm that all  labels are in place and easily 

readable from a reasonable distance. See 

Labeling diagram

 on p. 5.  

  DO NOT allow people to ride in the bulk bag or on the lifter. 

  DO NOT lift more than the rated load of the lifter or the bulk bag, whichever is smaller. The capacity of the lifter is 

4,000 pounds (1818.2 kg). If the capacity of your bulk bag is 3,300 pounds (1500kg), then you must not attempt to 

lift any more than 3,300 pounds.   

  DO NOT lift a load higher than necessary. Always travel with the bulk bag elevated only as high as necessary to 

avoid contact with the ground. Travel slowly. Avoid sudden stops to minimize load swing. Turn slowly and carefully. 

  DO NOT modify this product in any way. Modifications automatically void the 

Limited Warranty

 and might make 

the device unsafe to use. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Item 

Part no. 

Description 

Quantity 

47-514-007  Frame weldment 

08-145-028  48” nylon carriage strap with 

hook 

 

Exploded view and bill of materials 

Fork 

bracket 

Lifting bale 

Summary of Contents for BBL-4







Reviews: