background image

 

■For Your 

Safety 

Safety Instructions 

* Read the Safety Instructions carefully before use. Observe the instructions indicated herein to 

ensure safety.   

* Safety instructions in this manual are categorized into two types by the degree of danger 

associated with each action or condition. Based on analyses conducted by Vessel, all instructions 
mentioned in this manual are of the CAUTION level.   

* If the equipment is used in a manner not specified by the manufacturer, the protection provided by 

the equipment may be impaired.   
    WARNING 

Indicates that improper handling can lead to serious injury or even death. 

     CAUTION 

Indicates that improper handling can lead to minor injury and property 

damage. 

 

 

This symbol indicates a WARNING or CAUTION. 

 

This symbol indicates a prohibited action. 

 

This symbol indicates a mandatory required action 

 

 

CAUTIONS

 

  WARNING 

Do not use the N-3 in environments that require explosion-proofing. TheN-3 

is not of explosion-proof construction, therefore explosion or fire may occur. 

  WARNING 

Do not use the N-3 in flammable atmospheres. The corona discharge can 

act as an ignition source and cause an explosion or fire. 

  PROHIBITED 

Do not use the  N-3  in environments subjected to sharp temperature 

fluctuations or dewing. This kind of environment can lead to breakdown. 

  DO NOT WET 

Do not use the N-3 in highly damp places or anywhere it may be exposed to 

water, oil, solvent or other liquids. Contact with moisture can result in electric 

shock or breakdown. 

  PROHIBITED 

Do not use the  N-3  for any other purposes than static erasure or dust 

removal. 

  PROHIBITED 

Do not use the  N-3  with power supplies of ratings not specified in the 

specifications. Inappropriate power supplies can result in fire and electric 

shock. 

  PROHIBITED 

Do not install, use or service the N-3 until having understood the information 

in this instruction manual. 

  REMEMBER 

Keep this instruction manual in a safe handy place for future reference. 

 

 

Summary of Contents for STAT CLEAN N-3













Reviews: