background image

 Installation 

Installation Location 

Warning 

  PROHIBITED 

Do not use in environments with flammable gases and solvents in the atmosphere, 
requiring explosion-proof equipment. As this product is not explosion-proof, there is 
a risk of explosion or fire. 

 

Caution 

  Caution

 

 

Take into consideration the ambient conditions surrounding the installation 

location. 

 

Install indoors where it will be sheltered from wind and rain.   

 

Install in a location where it will not be exposed to water, oil or fine dust.   

 

Do not install in locations where considerable vibrations or shocks will be 

transmitted to the unit.   

 

Do not bring into areas with high humidity, or where there are corrosive gases 

such as acids, alkalis or chlorine gas exist. Also, do not use the product in these 
types of areas. There is a risk of electric shock or product breakdown.   

 

Please use in areas with a temperature between 0 to 45

, and a humidity of 10 to 

90%. 

Installation work 

Caution 

  REMEMBER 

 

Installation of the high voltage supply unit GP-1 should be conducted by 
someone proficient in handling of electric products, including electric wire.   

 

Do not, under any circumstances, drill holes into the GP-1.   

 

This product HPG-1 must be used while the high voltage supply unit GP-1 is fixed.   

Installing the GP-1 

Place the High Voltage Power Supply GP-1 close to the equipment on which the air gun HPG-1 is installed. 

Firmly secure it to a strong frame, wall, floor, etc. using four 

5 screws through the holes in the bottom of 

the  mounting  base.  When installing the GP-1 on a vertical surface, make sure the high voltage output 

connector is on the bottom. The GP-1 weighs approximately 4.5 kg. Please handle with great care to avoid 

serious injury due to the dropping of the GP-1 and alike. The GP-1 output can be configured from 3.5 to 

4.0kV. If the output is too high, a spark occurs at the gun tip part, and it may damage the equipment, so 

MAKE ABSOLUTELY SURE THAT THE OUTPUT VOLTAGE IS CORRECTLY SET ON THE GP-1

Connecting an Input Wire to the GP-1 

1. Prepare the power adaptor AD24-GP or AD24-GPE (2 types available as option for different plug shape). 

Insert the connector of the power adaptor AD24-GP or AD24-GPE into the input connector of the high 

voltage power supply unit GP-1 (MOLEX 5557-02R-210) and securely connect them. 

 

2. Connect the AC cable of the AD24-GP or the AD24-GPE to the power adaptor. Then, insert the 3-pin plug 

of the AC cable terminal into 

a grounded 3-pin outlet

. When you need to connect the AC cable to an 

ungrounded 2-pin outlet or the like, be sure to wire the ground terminal of the body of the GP-1 to a 

grounded machinery frame, etc. 

* In this case, make sure that the power switch on the GP-1 is in the OFF [o] position. 

* For details on how and where to install the GP-1, refer to the GP-1 instruction manual. 

Summary of Contents for HPG-1













Reviews: