VESPA LXV 50 Page 95 Service Station Manual Download

Page: 95 / 162

Soap-based lithium grease with NLGI 3; ISO-L-

XBCHA3, DIN K3K-20

Refitting the front wheel

- When refitting, tighten the 5 screws to the speci-

fied torque

Locking torques (N*m)

Nut tightening torque

20 to 25 N•m

Handlebar

Removal

Before carrying out these operations, remove the

instrument panel.

- After removing the transmissions and discon-

necting the electrical terminals, remove the termi-

nal fixing the handlebar to the steering.

- Check all components and replace faulty parts.

N.B.

IF THE HANDLEBAR IS BEING REMOVED TO REMOVE
THE STEERING, TILT THE HANDLEBAR FORWARD TO
AVOIDING DAMAGING THE TRANSMISSIONS.

Refitting

Carry out the operations in the reverse order to the

removal, observing the prescribed tightening tor-

que.

Locking torques (N*m)

Handlebar lock nut

45 ÷ 50

Vespa LXV 50

Suspensions

SUSP - 95

Summary of Contents for LXV 50



































































































































































Search results

Summary of Contents for LXV 50

Reviews:

Related manuals for LXV 50

Brands by name

Popular brands

VESPA LXV 50, Service Station Manual

Search results

Summary of Contents for LXV 50

Reviews:

Related manuals for LXV 50

Brands by name

Popular brands