Vertiv Liebert Mini-Mate MT036 Page 71 Installer/User Manual Download | Manualshive

Page: 71 / 80

background image

REV : 0
REV DATE : 06/18

DPN004806
Page :1 /1

F

or

m

N

o.

: D

P

N

00

10

40

_R

E

V

4

OPTIONAL FIELD INSTALLED

CONDENSATE PUMP CONNECTION LOCATIONS

3 TON MODEL

LIEBERT MINI-MATE

VARIABLE CAPACITY

Condensate Pump
Support Bracket

3/4" (19mm) NPT-Female

Condensate Drain

Connection

Field Supplied Rigid Piping

(Support as Required)

3/4" (19mm) NPT - Female

Customer Connection

1

Notes:

1. 3/4" NPT-Male to 3/4" (19mm) flexible rubber tubing assembly supplied must
be installed between condensate drain and pump inlet fitting and secured.

2.   The Auxiliary Float Switch included with pump must be field interlocked
      with unit control to enable unit shutdown feature.  Wire to Mini-Mate
      terminal per unit schematic.

3. Refer to DPN003401 for installation instructions.

4. Condensate pump is energized through Mini-Mate Module.
Separate power supply is not necesary.

5. Condensate pump includes built in drain line check valve.

CONDENSATE PUMP (FIELD INSTALLED)

ON UNIT WITH AIR OUTLET DUCTWORK

Air Outlet Duct

Fan Coil Unit

CONDENSATE PUMP (FIELD INSTALLED)

ON UNIT WITH AIR DISTRIBUTION PLENUM

3/4" (19mm) NPT-Female

Condensate Drain

Connection

Field supplied rigid piping.

Support as required.

Condensate Pump
Support Bracket

3/4" (19mm) NPT - Female
Customer Connection

3/8" (9.5mm) Compression Fitting
Drain Connection
Field Supplied Drain Line

Electrical Entrance

for Condensate Pump

Connection

Fan Coil Unit

1

Electrical Entrance

for Condensate Pump

Connection

3/8" (9.5mm) Compression Fitting
Drain Connection
Field Supplied Drain Line

«
...
69
70
71
72
73
...
»

Summary of Contents for Liebert Mini-Mate MT036

















































































Reviews:

No comments

Related manuals for Liebert Mini-Mate MT036

Brand: K&K Pages: 6

Brand: Fagor Pages: 10

Brand: Fagor Pages: 358

Brand: Fagor Pages: 556

Brand: Fagor Pages: 172

Brand: Fagor Pages: 180

Brand: Fagor Pages: 112

Master Control Unit

Brand: FaderMate Pages: 36

Brand: ICP DAS USA Pages: 7

I-2533CS Series

Brand: ICP DAS USA Pages: 8

Brand: Magellan Pages: 44

Brand: Namron Pages: 3

U1000 iQpump Drive

Brand: YASKAWA Pages: 426

Brand: YASKAWA Pages: 26

Brand: YASKAWA Pages: 210

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 400

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 466

Brand: Panasonic Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands