Vertiv Liebert MBX Busway Installer/User Manual Download Page 13 | Manualshive

Page: 13 / 16

Vertiv Liebert MBX Busway Installer/User Manual Download Page 13

4 FIRMWARE UPDATE

If the firmware for each device is not the latest available on the Socomec website, download the firmware
ZIP file for the module(s) to be updated. Firmware versions may be checked on the Socomec website:

https://www.socomec.com/product-upgrade-tool-software_en.html

.

To update a Socomec Digiware module firmware, perform the following steps:

1. Download the latest version of Socomec’s Product Upgrade Tool and firmware version from the page

above.

2. Install the Product Upgrade Tool on your laptop.
3. Connect the module to your laptop via USB – micro USB lead.
4. Open the Product Upgrade Tool program.
5. Verify the module to be upgraded is displayed in the Master field.
6. Click the

Browse

button and select the firmware ZIP file for the module.

7. Click

Update

and wait for the firmware upgrade to complete.

8. Configure the module per the instructions in section 1 or 2.

Figure 6.1 Product Upgrade Tool

4 Firmware Update

9

«
...
11
12
13
14
15
...
»

Summary of Contents for Liebert MBX Busway

















Reviews:

No comments