Vertiv Liebert IntelliSlot Unity Card Installer And User Manual Download Page 59

Page: 59 / 74

Modbus TCP Folder

The Modbus TCP permits connection to the card by:

•

Any client (Open) permits communication by any IP address

•

Clients on the same subnet as the Unity card

•

Clients with specific IP addresses (Trusted IP Lists); only five addresses are permitted

Modbus TCP Settings

Limit Network Access Type

IP Access List

•

Open

•

Same Subnet

•

Trusted IP List

Port

The TCP port used by the Modbus Server to listen for and respond to Modbus protocol requests.
Default = 502.

Maximum Client Connection Count

Maximum number of simultaneous connections allowed. Range: 1 to 5.

Modbus RTU Folder

Modbus RTU Settings

Node ID

Modbus Server ID for the interface; obtain from network administrator. Must be unique for each node
on the communication bus.

Baud Rate

Communication rate.

•

9600

•

19200

•

38400

Parity Check

The communication parity check.

•

None

•

Even

•

Odd

6 Editing the Unity Card Configuration

Summary of Contents for Liebert IntelliSlot Unity Card











































































Search results

Summary of Contents for Liebert IntelliSlot Unity Card

Reviews:

Related manuals for Liebert IntelliSlot Unity Card

Brands by name

Popular brands

Vertiv Liebert IntelliSlot Unity Card, Installer And User Manual

Search results

Summary of Contents for Liebert IntelliSlot Unity Card

Reviews:

Related manuals for Liebert IntelliSlot Unity Card

Brands by name

Popular brands