manualshive.com logo in svg

Vertiv eSure C48/58-1000B, Installation Manual, Page: 16 / 40

Share
Download
Vertiv eSure C48/58-1000B Installation Manual Download Page 16

 
 

Vertiv

 

|

 

eSure™ Power Extend Converter Mounting Bracket Kit Installation Manual (IM565460)

 

|

 

Rev. A 

16 

Figure 9:  

Connecting Power Extend Converter Load and Load Return Cables, 

Installing Power Extend Converter Return Wire Faston Tab (P/N 565990) 

 

 

[  ]  4.

 

Connect the return wire (P/N 564330) and return wire jumper (P/N 565752) provided with the 
power extend converter to the power extend converter return wire faston tab (P/N 565990) 
installed on the cabinet’s return bar in the step above.  See 

Figure 10

. 

[  ]  5.

 

Route the return wire (P/N 564330) as shown in 

Figure 10

, then connect it to the power extend 

converter.  Orient the white square on the return wire faston receptacle’s locking tab as shown in 

Figure 10

. 

Installed View

Cabinet

Return Bar

Distribution

Panel Load

Busbars

Connect

Power Extend Converter

Load Lead Here

(Torque to 72 in-lbs)

Connect

Power Extend Converter

Load Return Lead Here

(Torque to 72 in-lbs)

Power Extend Converter

Return Wire Faston Tab

(P/N 565990)
Load Return

Lead Lug

1/4” Flat Washer

1/4” Lock Washer

1/4-20 Nut (Torque to 72 in-lbs)

Summary of Contents for eSure C48/58-1000B









































Reviews:

No comments