background image

Energy (kWh)

Output power

Load Status Options

Sout (kVA)

Apparent output power

Pout (kW)

Active output power

Power factor

Power factor of output power

Load percent (%)

Percentage of recent power rated to output power

4.2.4 Settings Submenu

The settings screen consists of tabs that list UPS settings for configuration and adjusting parameters
with tabs for:

Input

Output

Battery

Monitor

System

Outlet1

NOTE: Do not change parameter settings or reset to factory defaults when powering-off the UPS.

To modify UPS settings:

1. At the main menu, select the Settings icon, and press Enter.
2. When prompted Enter the Settings password. Use the arrow buttons to increase the digit or

change to the next digit. Press Enter when finished. The default Settings password is 111111 (six
ones).

3. Use the arrow buttons to move the cursor left/right and select a tab. Then press Enter to

navigate the option list for the selected tab.

4. Use the arrow buttons to move the cursor through the options. Press Enter to modify the

selected option. Use the arrow buttons to change the setting. Press Enter to confirm the
selection or ESC to cancel the selection.

5. Press ESC to exit from the option list and return to the tab selection. Press ESC again to return

to the main menu.

NOTE: Parameter settings are password protected, for details see

Editing Display and Operation

Settings

.

4 Operations

21

Liebert® EDGE Installer/User Guide

Summary of Contents for EDGE-1000IMT





































































Reviews: