manualshive.com logo in svg

Versitron Web Smart+ SG71070M, User Manual, Page: 6 / 123

Share
Download
Versitron Web Smart+ SG71070M User Manual Download Page 6

vi 

SG71070M 

    Revision A3

 

3-6 IGMP Snooping

 ................................................................................................................................... 96

 

3-6.1 Status

 ..................................................................................................................................................... 96

 

3-6.2 Group Information

 ............................................................................................................................... 98

 

3-6.3 IPv4 SSM Information

 ......................................................................................................................... 99

 

3-7 VLANS

 ................................................................................................................................................. 100

 

3-7.1 VLAN Membership

 ............................................................................................................................ 100

 

3-7.2 VLAN Port

 ........................................................................................................................................... 101

 

3-8 Loop Protection

 ................................................................................................................................. 103

 

3-9 LLDP

 .................................................................................................................................................... 104

 

3-9.1 LLDP information

 ............................................................................................................................... 104

 

3-9.2 LLDP-MED Neighbor

 ......................................................................................................................... 106

 

3-9.3 LLDP Statistics

 .................................................................................................................................... 110

 

CHAPTER 4        DIAGNOSTICS

........................................................................................ 112

 

4-1 Ping

 ..................................................................................................................................................... 112

 

4-2 Cable Diagnostics

 .............................................................................................................................. 113

 

4-3 Traceroute

 .......................................................................................................................................... 114

 

CHAPTER 5        MAINTENANCE

 ..................................................................................... 115

 

5-1 Restart Device

 .................................................................................................................................... 115

 

5-2 Firmware

 ............................................................................................................................................. 116

 

5-2.1 Firmware Upgrade

 ............................................................................................................................. 116

 

5-3 Configuration

 .................................................................................................................................... 117

 

5-3.1 Save startup-config

 ........................................................................................................................... 117

 

 

Revision History 

Release 

Date 

Revision 

0.81.2 

07/24/2016 

A1 

0.82.2 

10/06/2016 

A2 

0.83.2 

12/10/2016 

A3 

 

 

 

Summary of Contents for Web Smart+ SG71070M




























































































































Reviews:

No comments