manualshive.com logo in svg

Versitron Web Smart+ SG71070M, User Manual, Page: 17 / 123

Share
Download
Versitron Web Smart+ SG71070M User Manual Download Page 17

11 

SG71070M 

    Revision A3

 

2-1.5 Log 

The log is standard for logging program messages . It allows separation of the software that 
generates messages from the system that stores them, and the software that reports and 
analyzes them. It can be used as well for generalized information, analysis and debugging 
messages. It is supported by a wide variety of devices and receivers across multiple platforms.   

Web Interface   

To configure System Log Configuration in the web interface: 

1.

 

Click Configuration, System and log. 

2.

 

Specify the syslog parameters include IP Address of Syslog server and Port number. 

3.

 

Evoke the Syslog to enable it. 

4.

 

Click Apply.   

 

Figure2-1.5:    The System Log Configuration 

 

Parameter description: 

 

Server Mode   

Indicate the server mode operation. When the server mode operation is enabled, the syslog 
message will send out to syslog server. The syslog protocol is based on UDP communication 
and received on UDP port 514.    The syslog server will not send acknowledgments back to 
the sender since UDP is a connectionless protocol and it does not provide 
acknowledgments. The syslog packet will always send out even if the syslog server does not 
exist. Possible modes are:   

Enabled: Enable server mode operation.   

Disabled: Disable server mode operation.   

 

Server Address   

Indicates the IPv4 hosts address of syslog server. If the switch provide DNS feature, it also 
can be a host name.     

 

Buttons 

These buttons are displayed on the Log page: 

Apply – Click to save changes. 

Reset - Click to undo any changes made locally and revert to previously saved values. 

 

 

 

Summary of Contents for Web Smart+ SG71070M




























































































































Reviews:

No comments