Introduction
Thank you for purchasing the M7260PA 10/100/1000Base PoE (PSE)
Media Converter. This product supports IEEE802.3U, IEEE802.3z
1000Base-Tx/Fx protocol and IEEE802.3af PoE PSE protocol. The
M7260PA provides either 25W (48VDC/540mA) or 15.4W
(48VDC/350mA) power along the CAT5 twisted-pair cable. The
following manual is for your reference.
Packing List
Please check the following items in the package before installing the
media converter.
•
M7260PA Media Converter
•
Power
Cable
Please contact VERSITRON immediately if any of the above items are
missing or damaged.
Installation
The RJ-45 connector supports 10/100/1000Mbps transmission speeds
over CAT5 twisted-pair (TP) with a maximum length of 100meters.
The fiber port supports duplex and simplex 1000Base fiber optic SFP
modules with LC connectors which are sold separately. When
connecting the fiber in a duplex application, be sure that the transmitter
(TX) on one end of the fiber is connected to the receiver (RX) on the
other end of the fiber. For simplex applications this is not applicable.
AC power is supplied by connecting the AC power cord to the AC input
jack of media converter and an AC power source.
Connections
The network device (work station, hub or switch) with an RJ-45 interface
is connected to RJ-45 jack of media converter using a Cat5 cable. The
multi-mode or single-mode fiber is connected to the LC fiber connector
on the fiber optic SFP module. Apply power to the M7260PA.
LED Indicators
PWR
ON when power is applied
Link/Act
(FX)
ON when fiber signal is detected
Blinking when receiving data
Link/Act
(TP)
ON when copper signal is detected (TP)
Blinking when receiving data
FDX
(TP)
ON when TP link is in full duplex mode
OFF when TP link is in half duplex mode
1000M
ON 1000M
OFF 100M or 10M
100M
ON 100M
OFF 1000M (1000M ON) or 10M (1000M OFF)
POE
ON when connected to a proper PD load
OFF when no load or wrong load
Blinking when load is abnormal
PWR
ON when POE 48V power is ok
OFF when POE 48V power is lost or too low
Main Features
1. IEEE802.3U, IEEE802.3z, 1000Base-Tx/Fx standard.
2. IEEE802.3af PoE PSE compatible.
3. Half duplex: back pressure flow control
Full duplex: IEEE802.3x flow control
4. Automatic identification of MDI/MDI-X.
Technical Parameters
1. Standard Protocol: IEEE 802.3u 100 Base-TX, IEEE802.3z,
IEEE802.3ab standard, IEEE802.3af
2. Connector: one UTP RJ-45 connector, one LC connector
3. Operation mode: full duplex mode or half duplex mode
4. Power supply parameter: 100-240V AC
5. Environmental temperature: 0
°
C
-
50
°
C
6. Relative humidity: 5%-90%
7. TP cable: Cat5 UTP cable
8. Optical fiber:
Multi-Mode: 50/125, 62.5/125
Single-Mode: 8.3/125, 8.7/125, 9/125
9. Dimensions: 5.51 x 4033 x 1.57 Inches (140 x 110 x 40 mm)
Cautions
1. This product is suitable for indoor applications.
2. Use dust cover for the fiber interface when not in use.
3. Do not look into the fiber interface with the naked eye.
M7260PA
10/100/1000M PoE (PSE)
Ethernet Media Converter
User’s Manual
© July 2014
VERSITRON, Inc.
83 Albe Drive / Suite C
Newark, DE 19702
800-537-2296
www.versitron.com
