manualshive.com logo in svg

VersaLogic Owl, Hardware Reference Manual

Share
Download
VersaLogic Owl Hardware Reference Manual Download Page 55

VL-CBR-4005B Paddleboard 

55 

VL-EPU-4012 Hardware Reference Manual 

 

User I/O Connector 

This figure shows the location and pin orientation of the user I/O connector. 

Figure 29. Location and Pin Orientation of the User I/O Connector 

 

Table 17: User I/O Connector Pinout 

Pin 

Signal 

 

Pin 

Signal 

1 

+5 V 

 

2 

GND 

3 

USB1_P 

 

4 

USB2_P 

5 

USB1_N 

 

6 

USB2_N 

7 

+5V 

 

8 

GND 

9 

USB3_P 

 

10 

USB4_P 

11 

USB3_N 

 

12 

USB4_N 

13 

+3.3 V (

Note 1

) 

 

14 

GND 

15 

SPKR# 

 

16 

PLED# 

17 

PWR_BTN# 

 

18 

RST_BTN# 

19 

GND 

 

20 

GND 

21 

I2C Clock 

 

22 

V_BATT 

23 

I2C Data 

 

24 

V_BATT RETURN 

25 

GND 

 

26 

GND 

27 

GPIO1 

 

28 

GPIO2 

29 

GPIO3 

 

30 

GPIO4 

31 

GND 

 

32 

GND 

33 

GPIO5 

 

34 

GPIO6 

35 

GPIO7 

 

36 

GPIO8 

37 

+3.3 V (

Note 2

) 

 

38 

GND 

39 

ETH0 LED 

 

40 

ETH1 LED 

Summary of Contents for Owl








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands