manualshive.com logo in svg

VersaLogic Owl, Hardware Reference Manual

Share
Download
VersaLogic Owl Hardware Reference Manual Download Page 45

Video Interfaces 

45 

VL-EPU-4012 Hardware Reference Manual 

 

Video Interfaces 

The Intel Atom E39xx processor series contains an integrated graphics engine with advanced 
2D/3D graphics, video decode and encode capabilities, and a display controller. The Owl 
provides the following video interfaces: 

 

One Mini Disp+ connector 

 

One LVDS display connector; a 4-pin LVDS backlight connector is also provided  

Mini Disp+ Connector 

DisplayPort consists of three interfaces: 

 

Main Link – transfers high-speed isochronous video and audio data 

 

Auxiliary channel – used for link management and device control; the EDID is read over this 
interface 

 

Hot Plug Detect – indicates that a cable is plugged in 

The DisplayPort interface supports: 

 

Audio signaling 

 

DP++ mode allowing connection to an HDMI device through a passive adapter. “Passive” 
means that the adapter does not require external power (because it uses the DP port’s 3.3 V 
power) and it does not require software drivers. 

The next figure shows the location of the 20-pin Mini Disp+connector. Table 13 lists the 
pinout of the Mini Disp+ connector. 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for Owl








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands