VersaLogic Blackbird VL-EPU4462 Hardware Reference Manual Download Page 73

Page: 73 / 74

Thermal Considerations

VL-EPU-4562/4462 Reference Manual

Installing the VL-HDW-418 Heat Sink Fan

1. Position the fan assembly



Using the figure below as a guide, align the mounting holes of the heat sink fan with the

four holes in the passive heat sink. Position the fan so that its power cable can easily

reach its mating connector (J18).

2. Secure the fan to the heat sink



Affix the heat sink fan using four M3 pan head screws.



Using a torque screwdriver, tighten the screws to 4.0 inch-pounds.

3. Connect power to the fan



Connect the fan’s power cable to J18 on the EPU-4562/4462.

Figure 36. Installing the Heat Sink Fan

Summary of Contents for Blackbird VL-EPU4462











































































Search results

Summary of Contents for Blackbird VL-EPU4462

Reviews:

Related manuals for Blackbird VL-EPU4462

Brands by name

Popular brands

VersaLogic Blackbird VL-EPU4462, Hardware Reference Manual

Search results

Summary of Contents for Blackbird VL-EPU4462

Reviews:

Related manuals for Blackbird VL-EPU4462

Brands by name

Popular brands