VersaLogic Blackbird VL-EPU4462 Hardware Reference Manual Download Page 72

Page: 72 / 74

Thermal Considerations

VL-EPU-4562/4462 Reference Manual

Installing the VL-HDW-417 Passive Heat Sink

1. Apply the Arctic Silver

Thermal Compound (VL-HDW-401)



Apply the thermal compound to the heat plate using the method described on the Arctic

Silver website -

http://www.arcticsilver.com/

2. Position the passive heat sink



Using the next figure as a guide, align the seven mounting holes of the heat sink with the

heat plate.



Orient the heat sink fins in the direction of the system airflow to maximize CPU cooling.

3. Secure the passive heat sink to the heat plate



Affix the passive heat sink to the heat plate using seven M2.5 pan head screws.



Using a torque screwdriver, tighten the screws to 4.0 inch-pounds.

Figure 35. Installing the Passive Heat Sink

Summary of Contents for Blackbird VL-EPU4462











































































Search results

Summary of Contents for Blackbird VL-EPU4462

Reviews:

Related manuals for Blackbird VL-EPU4462

Brands by name

Popular brands

VersaLogic Blackbird VL-EPU4462, Hardware Reference Manual

Search results

Summary of Contents for Blackbird VL-EPU4462

Reviews:

Related manuals for Blackbird VL-EPU4462

Brands by name

Popular brands