VersaLogic Blackbird VL-EPU4462 Hardware Reference Manual Download Page 16

Page: 16 / 74

Configuration and Setup

VL-EPU-4562/4462 Reference Manual

Jumper Blocks

Jumper As-Shipped Configuration

Figure 4. Jumpers As-Shipped Configuration

Jumper Configuration Summary

Table 1: Jumper Block Configurations

Jumper

Block

Pins

Function

Description

1-2

COM1 Endpoint

Termination



Jumper In: Endpoint termination (for RS-485 or RS-422)



Jumper Out: Not terminated (RS-232) (default)

3-4

COM2 Endpoint

termination



Jumper In: Endpoint termination (for RS-485 or RS-422)



Jumper Out: Not terminated (RS-232) (default)

1-2

COM3 Endpoint

Termination



Jumper In: Endpoint termination (for RS-485 or RS-422)



Jumper Out: Not terminated (RS-232) (default)

3-4

COM4 Endpoint

termination



Jumper In: Endpoint termination (for RS-485 or RS-422)



Jumper Out: Not terminated (RS-232) (default)

Summary of Contents for Blackbird VL-EPU4462











































































Search results

Summary of Contents for Blackbird VL-EPU4462

Reviews:

Related manuals for Blackbird VL-EPU4462

Brands by name

Popular brands

VersaLogic Blackbird VL-EPU4462, Hardware Reference Manual

Search results

Summary of Contents for Blackbird VL-EPU4462

Reviews:

Related manuals for Blackbird VL-EPU4462

Brands by name

Popular brands