VersaLogic Blackbird VL-EPU4462 Hardware Reference Manual Download Page 14

Page: 14 / 74

Configuration and Setup

VL-EPU-4562/4462 Reference Manual

Figure 3. Typical Development Configuration

1. Attach Cables and Peripherals



Attach a VGA monitor to either of the baseboard’s Mini Disp+ connectors using a

VL-CBR-2032.



Attach a SATA hard disk to the either of the baseboard’s SATA connectors using a VL-

CBR-0701 or VL-CBR-0702 cable.



Attach a VL-CBR-4005B paddleboard to the baseboard’s User I/O connector.



Connect a USB keyboard and USB mouse to one of the USB Type-A connectors on the VL-

CBR-4005B paddleboard.



Attach a USB CD-ROM drive to one of the USB Type-A connectors on the VL-CBR-4005B

paddleboard.

2. Connect Power Source



Plug the power adapter cable VL-CBR-0809 into the main power connector on the

baseboard. Attach the motherboard connector of the ATX power supply to the adapter.



Attach an ATX power cable to any 3.5-inch drive that is not already attached to the power

supply (hard drive or CD-ROM drive).

Summary of Contents for Blackbird VL-EPU4462











































































Search results

Summary of Contents for Blackbird VL-EPU4462

Reviews:

Related manuals for Blackbird VL-EPU4462

Brands by name

Popular brands

VersaLogic Blackbird VL-EPU4462, Hardware Reference Manual

Search results

Summary of Contents for Blackbird VL-EPU4462

Reviews:

Related manuals for Blackbird VL-EPU4462

Brands by name

Popular brands