background image

36

Save  These  Instructions                                                                                                                          

Vermont Castings  •  Aspen 1920 Owner's Manual_R32 • 08/17

4021-645J • 08-03-17

3

This warranty is void if:

•  The appliance has been over-fired, operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals. 

Over-firing can be identified by, but not limited to, warped plates or tubes, deformation/warping of interior cast iron structure or 

components, rust colored cast iron, bubbling, cracking and discoloration of steel or enamel finishes. 

•  The appliance is subjected to prolonged periods of dampness or condensation.

•  There is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited 

to, improper chimney or venting installation.

LIMITATIONS OF LIABILITY

•  The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or implied, or in 

contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no event will HHT be liable for 

any incidental or consequential damages caused by defects in the appliance. Some states do not allow exclusions or limitation of 

incidental or consequential damages, so these limitations may not apply to you. This warranty gives you specific rights; you may also 

have other rights, which vary from state to state. EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES 

OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE 

EXPRESSED WARRANTY SPECIFIED ABOVE.

Summary of Contents for The Aspen 1920







































Reviews: