background image

 

 

 

 

 

STEP 38 Cont: Back each screw out of its manifold 4 complete turns.  Screw the manifold 

to the door until snug.  Secure the wide end of each manifold to the inside 
door face with 2 each, Phillips pan head machine screws (10-20x ¾”).  
Remember to place the upper centre glass retainer clip under the wide end 
of the right door manifold.  Install the right and left door hinge bosses. 
 
Centre the bosses and secure with 3 each, hex head leveler bolts – (¼-20x 
½” flat head) and 3 each, ¾” o.d. flat washers (¼”).  Tighten just past 
finger tight.  Install the upper (long) hinge pins in the right and left hinge 
bosses by tapping them into their drillings with a brass faced hammer.  
Install the jump rings on the upper shoulder of the lower (short) door pins 
and tap the pins into their drillings in the bottom of the right and left hinge 
bosses with a brass faced hammer.  Insert the socket set screw (7/16- 
20x1”) into its tapped hole in the top centre of the right door.  Screw the 
set screw through the door (from inside) until the socket end is flush with 
the bottom of the gasket channel.  Re-cement the gasket. 
 

STEP 39: 

Cleaning, washing and taping the stove.  With the putty knife, clean all 
outside stove seams and joints of any thermocement leakage or spillage.  
Draw a bucket or pail of hot water and with a sponge or soft rag; wash the 
stove down, especially the outside seams and joints.  Remove all visible 
dirt and thermocement.  Mask the damper handle stub and thermostat 
handle with masking tape.  Cover the secondary air system cover plate and 
the printed plates on the catalyst access panel with masking tape. 

 
STEP 40: 

Paint the stove.  Use 

Vermont Castings

 High Temperature Stove Paint 

(black), part # 000-0031.  Follow directions printed on the can and paint 
the entire outside of the stove. 

 
STEP 41: 

Install and adjust the doors.  Locate the hinge pin drillings in the upper 
sides of the stove front.  Insert the upper hinge pins of each door into its 
drillings, swing the bottom of each door against the stove front and drop 
the lower hinge pins into their drillings.  Close the doors and check the 
gasket seating between the doors and the stove front mating surface.  Both 
door bottoms should be level and even with each other.  There should be 
no metal to metal contact between the doors and the stove front or 
between the right and left doors.  The vertical seam between the doors 
should be even from top to bottom.  Adjust the doors by gently tapping 
left or right and up and down.  When a good gasket seal is achieved and 
doors are even and level, tighten the leveling bolts (3 per door).  Install the 
door handle by screwing it onto the socket set screw protruding from the 
top centre of the right door.  With the door handle flush against the door 
face, the handle tab should enter its slot in the top centre of the stove front  

Summary of Contents for Deviant Encore 0028
























































Reviews: