background image

Installation Instructions and 

Homeowner’s Manual

WARNING! 

IF THE INFORMATION IN THIS 
MANUAL IS NOT FOLLOWED 
EXACTLY, A FIRE OR EXPLOSION 
MAY RESULT CAUSING 
PROPERTY DAMAGE, PERSONAL 
INJURY OR LOSS OF LIFE.

FOR YOUR SAFETY

DO NOT STORE OR USE  
GASOLINE OR OTHER 
FLAMMABLE VAPORS AND 
LIQUIDS IN THE VICINITY OF 
THIS OR ANY OTHER 
APPLIANCE.

PLEASE READ THIS MANUAL 
BEFORE INSTALLING AND 
USING APPLIANCE

Installation and service must 
be performed by a qualified
installer, service agency or
the gas supplier.

WHAT TO DO IF YOU SMELL GAS:

•  Do not try to light any appliance. 
•  Do not touch any electric switch; 
•  Do not use any phone in your  

building. 

•  Immediately call your gas supplier 

from your neighbor’s phone. Follow 
the gas suppliers instructions. 

•  If you cannot reach your gas 

supplier call the fire department.

INSTALLER/CONSUMER 

SAFETY INFORMATION

Chateau

 

Direct Vent Decorative 
Gas Appliance

Model:  DVT38S2

CERTIFIED

DESIGN

CERTIFIED

20009543  1/07  Rev. 7

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

Summary of Contents for Chateau DVT38S2









































Reviews: