background image

Vermont Castings  •  Apsen C3 Installation Manual_R2  •  2019 - ___ •  07/19

7

8390-950i

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation manual

Customer:

Date Installed:
Lot/Address:
Location of Appliance:
Installer:
Dealer/ Distributor Phone #:
Serial #:

Model :

WARNING! Risk of Fire or Explosion!

 Failure to install appliance according to these instructions can lead to a fi re or explosion.

Appliance Install

YES

IF NO, WHY?

Verifi ed clearance to combustibles.

Appliance is leveled and connector is secured to appliance.

Hearth extension size/height decided.
Outside Air Kit Installed.

Floor protection requirements have been met.

If appliance is connected to a masonry chimney, it should be cleaned and 

inspected by a professional. If installed to a factory built metal chimney, 

the chimney must be installed according to the manufacturer’s instructions 

and clearances.

Chimney

Chimney confi guration complies with diagrams.
Chimney installed, loked and secured in place with proper clearance.
Chimney meets recommended height requirements (16 Feet).
Roof fl ashing installed and sealed.

Terminations installed and sealed.

Clearances

Combustible materials not installed on non-combustible areas.
Verifi ed all clearances meet installation manual requirements.

Mantels and wall projections comply with installation manual requirements.
Protective hearth strips and hearth extensions installed per manual 

requirements.

Appliance Setup

All packaging and protective materials removed.
Firebrick, baffl e and ceramic blanket insalled correctly

All labels have been removed from the door.

All packaging materials are removed from inside/under the appliance.
Manual  bag  and  all  of  its  contents  are  removed  from  inside/under  the 

appliance and given to the party responsible for use and operation.

Hearth & Home Technologies recommends the following:

•  Photographing the installation and copying this checklist for your fi le.
•  That this checklist remain visible at all times on the appliance until the installation is complete.

Comments:

 Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action needed:

Comments 

communicated 

to 

party 

responsible 

    by 

   on

(Builder/Gen. Contractor)

(Installer)

(Date)

F. Install Checklist

Summary of Contents for Aspen C3





















Reviews: