manualshive.com logo in svg

Vermeer 504 PRO, Operator And Maintenance Manual

Share
Download
Vermeer 504 PRO Operator And Maintenance Manual Download Page 25

504PRO_604PRO_o-m2_00

-

2-12 Safety Messages

504/604 PRO Baler

2.5

Fire Prevention Baler

Figure 1. Do not smoke in the vicinity of the machine.

The harvested crop can easily ignite! To prevent fire:

•

Remove crop remains and oil leaks.

•

If any machine parts run hot: find and remove cause.

•

Keep the electrical systems of tractor and baler and the exhaust system of the tractor in proper condition.

•

The existing wiring must not be used for any other purposes than those installed in the factory or approved by the manufacturer. Overloading
the electrical lines leads to excessive heating.

Fire extinguisher (option)

–

Refill

A 2.5 gal (9.5 liter) pressurized water fire extinguisher is recommended to be carried on the tractor or baler.

Figure 2. A fire extinguisher can be mounted to the rails of the maintenance platform.

https://tractormanualz.com

Summary of Contents for 504 PRO


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands