background image

WARNING! MOVING LOAD HAZARD
Operating the product when people are underneath or near the load could cause
serious injury or death.
When operating the product, make sure that there are no people who are situated
underneath or near the load.
Keep yourself and bystanders away from the danger zone during lifting.
Never place a load over people.

1.

Ensure that the landing area is clear of people and obstacles. Do not move the load before
ensuring that it is properly attached to the lifting device.

2.

If the hoist has an alarm horn, press the alarm horn push button to warn people nearby
that a load is about to be moved.

6 OPERATION

This document and the information contained herein, is the exclusive property of Verlinde S.A.S and represents a non-
public, confidential and proprietary trade secret that may not be reproduced, disclosed to third parties, altered or
otherwise employed in any manner whatsoever without the express written consent of Verlinde S.A.S. Copyright 2020
© Verlinde S.A.S. All rights reserved.

6/2020

Summary of Contents for STAGEMAKER 100618073

























































































































Reviews: