VERDER VA 50 Instructions-Parts List Manual Download | Manualshive

Page: 33 / 36

background image

819.4496

33

Technical Data

Maximum Fluid Working Pressure

8.3 bar

Air Pressure Operating Range

1.4–8.3 bar

Maximum Air Consumption

4.9 N m

3

/min

Air Consumption
at 4.9 bar/227 l/min

1.68 N m

3

/min (see chart)

Maximum Free Flow Delivery

568 l/min

Maximum Pump Speed

145 cpm

Liters per cycle

3.90

Maximum Suction Lift

5.48 m wet or dry

Maximum Size Pumpable Solids

6.3 mm

* Sound pressure Level at 7 bar, 50 cpm

90 dBa

* Sound Power Level at 7 bar, 50 cpm

103 dBa

* Sound Pressure Level at 4.9 bar, 50 cycles/min 85 dBa
Maximum Operating Temperature

65.5°C

Air Inlet Size

1/2 npt(f)

Fluid Inlet Size.

2 in. Raised Face Flange

ANSI/DIN 50 Flange

2 in. (50 mm)

Fluid Outlet Size.

2 in. Raised Face Flange

ANSI/DIN 50 Flange

2 in. (50 mm)

Wetted Parts

Vary by Model. Refer to pages 26–2 9

Non-wetted External Parts

Aluminum,

302, 316 Stainless Steel, Polyester (labels)

Weight

Polypropylene Pumps

with Aluminum Air Section: 22 kg

PVDF Pumps

with Aluminum Air Section: 31 kg

Polypropylene Pumps

with Stainless Steel Air Section: 32 kg

PVDF Pumps

with Stainless Steel Air Section: 41 kg

Santoprene

®

is a registered trademark of the Monsanto

Co.

*

Sound pressure levels measured with the pump
mounted on the floor, using Rubber Foot Kit 819.4333.
Sound power measured per ISO Standard 9614–2.

Fluid Temperature Range

* The maximum temperature listed is based on the ATEX standard for T4 temperature classification. If you are
operating in a non-explosive environment, FKM fluoroelastomer’s maximum fluid temperature in aluminum or
stainless steel pumps is 320°F (160°C).

NOTICE

Temperature limits are based on mechanical stress only. Certain chemicals will further limit the fluid temperature
range. Stay within the temperature range of the most-restricted wetted component. Operating at a fluid temperature
that is too high or too low for the components of your pump may cause equipment damage.

Diaphragm/Ball/Seat Material

Fluid Temperature Range

Aluminum, Hastelloy, or

Stainless Steel Pumps

Polypropylene or

Conductive

Polypropylene Pumps

PVDF Pumps

Fahrenheit

Celsius

Fahrenheit

Celsius

Fahrenheit

Celsius

Acetal (

AC

)

10° to 180°F

-12° to 82°C

32° to 150°F

0° to 66°C

10° to 180°F

-12° to 82°C

Buna-N (

BN

)

10° to 180°F

-12° to 82°C

32° to 150°F

0° to 66°C

10° to 180°F

-12° to 82°C

FKM Fluoroelastomer (

FK

)*

-40° to 275°F

-40° to 135°C

32° to 150°F

0° to 66°C

10° to 225°F

-12° to 107°C

Geolast

®

(

GE

)

-40° to 150°F

-40° to 66°C

32° to 150°F

0° to 66°C

10° to 150°F

-12° to 66°C

Polychloroprene overmolded

diaphragm (

CO

) or Poly-

chloroprene check balls
(

CR

or

CW

)

0° to 180°F

-18° to 82°C

32° to 150°F

0° to 66°C

10° to 180°F

-12° to 82°C

Polypropylene (

PP

)

32° to 150°F

0° to 66°C

32° to 150°F

0° to 66°C

32° to 150°F

0° to 66°C

PTFE overmolded

diaphragm (

PO

)

40° to 180°F

4° to 82°C

40° to 150°F

4° to 66°C

40° to 180°F

4.0° to 82°C

PTFE check balls or two-piece
PTFE/EPDM diaphragm (

PT

)

40° to 220°F

4° to 104°C

40° to 150°F

4° to 66°C

40° to 220°F

4° to 104°C

PVDF (

PV

)

10° to 225°F

-12° to 107°C

32° to 150°F

0° to 66°C

10° to 225°F

-12° to 107°C

Santoprene

®

(

SP

)

-40° to 180°F

-40° to 82°C

32° to 150°F

0° to 66°C

10° to 180°F

-12° to 82°C

TPE (

TP

)

-20° to 150°F

-29° to 66°C

32° to 150°F

0° to 66°C

10° to 150°F

-12° to 66°C

«
...
31
32
33
34
35
...
»

Summary of Contents for VA 50





































Reviews:

No comments

Related manuals for VA 50

Altherma 3 R F+W

Brand: Daikin Pages: 20

Brand: Dantherm Pages: 12

Brand: Sierra Pages: 11

UFLEX SilverSteer UP25 F-SVS

Brand: Ultraflex Pages: 29

Brand: ACE INSTRUMENTS Pages: 3

Brand: Agilent Technologies Pages: 306

Brand: Power Fist Pages: 20

EVERPURE CONSERV LT-S

Brand: Pentair Pages: 20

HYDROMATIC HTS33A1

Brand: Pentair Pages: 8

Brand: Rheem Pages: 1

Brand: HERBORNER pumpentechnik Pages: 39

Brand: Santon Pages: 12

Brand: samhydraulik Pages: 14

Brand: EBARA Pages: 40

Brand: CareFusion Pages: 28

Brand: SuperFish Pages: 8

Brand: Williamson Pages: 8

FLYGT Flygt 2071

Brand: Xylem Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands