background image

• Use shielded cables for all system and zone bus cables.
• Refer to the 

Verasys BACnet MS/TP Communications Technical Bulletin (LIT-12012362)

 for detailed

information about wire size and cable length requirements for the zone bus.

Table 9: ZEC510 wiring details

Terminal

Terminal

labels

Function and electrical ratings and

requirements

Cable type and length

IN1

Provides an AI connection for discharge air (DA-T)

sensor.

0.6 mm (22 AWG) stranded, 2-

wire twisted cable for runs of

<30 m (<90 ft).

IN2

Provides a BI connection for occupancy sensor dry

contact (optional).

n/a

Analog Input (AI)

IN3

Provides an AI connection for supply air (SA-T)

sensor.

0.6 mm (22 AWG) stranded, 2-

wire twisted cable for runs of

<30 m (<90 ft).

OUT1

Provides a BO connection for box heating stage 1.

Internal power source: 24 VAC power, 

24~ HOT.

See guideline C in Table 10

OCOM1

Provides a BO connection for box heating stage

1. Connects 

OCOM1

 to 

24~ COM 

when activated.

Internal power source: 30 VAC maximum voltage

to load, 0.5 A maximum output current, 40 mA

minimum load current.

See guideline C in Table 10

OUT2

Provides a BO connection for box heating stage 2.

Internally sources 24 VAC power, 

24~ HOT.

See guideline C in Table 10

OCOM2

Provides a BO connection for box heating stage

2. Connects 

OCOM2

 to 

24~ COM

 when activated.

Internal power source: 30 VAC maximum voltage

to load, 0.5 A maximum output current, 40 mA

minimum load current.

See guideline C in Table 10

OUT3

Provides a BO connection for box fan.

Internal power source: 24 VAC power, 

24~ HOT.

See guideline C in Table 10

OCOM3

Provides a BO connection for box fan. Connects

OCOM3

 to

 24~ COM

 when activated.

Internal power source: 30 VAC maximum voltage

to load, 0.5 A maximum output current, 40 mA

minimum load current.

See guideline C in Table 10

OUT4

Provides a BO connection for supplemental heat.

Connects 

OUT4 

to 

OCOM4

 when activated.

Note: 

Requires external power source:

30 VAC maximum voltage to load, 0.5 A

maximum output current, 40 mA minimum

load current.

See guideline C in Table 10

OCOM4

Provides a BO connection for supplemental heat.

Note: 

This common is isolated from all other

commons, so jumper 

24~ COM

 terminal if in

use.

See guideline C in Table 10

OUT5

Provides a BO connection for box heating stage 3.

Connects 

OUT5

 to 

OCOM5

 when activated.

Note: 

Requires external power source:

30 VAC maximum voltage to load, 0.5 A

maximum output current, 40 mA minimum

load current.

See guideline C in Table 10

Binary Output (BO)

for VAV with staged

reheat control

OCOM5

Provides a BO connection for box heating stage 3.

Note: 

This common is isolated from all other

commons, so jumper 

24~ COM

 terminal if in

use.

See guideline C in Table 10

Verasys ZEC510 VAV Controllers Installation Guide

20

Summary of Contents for ZEC510



































Reviews: