background image

44

8 Dismount

VEGASOURCE 82 • Source holder

66076-EN-230810

8 Dismount

8.1  Dismounting steps

As soon as a radiometric measuring system is no longer required, the 

radiation must be switched off on the source holder (position " 

OFF

"). 

The source holder must be dismounted under consideration of all 

relevant regulations and stored in a lockable room without through 

traffic.

Inform the responsible authorities of this measure.
The access area for this storage room must be measured (µSv/h 

resp. mR/h) and marked. The radiation safety officer is responsible for 

implementing anti-theft measures.
Care must be taken that the source in the source holder is not 

scrapped together with the rest of the system.
Arrange for a return shipment as soon as possible.

Caution:

Dismounting may only be carried out by authorized, qualified person

-

nel who are monitored for radiation exposure according to local laws 

or the handling permit. Take note of the specifications in the existing 

handling permit.
All local conditions must be taken into account.
All work must be carried out in the shortest possible time and at the 

largest possible distance (shielding). Also, the endangering of other 

persons must be avoided through suitable measures (e.g. safety 

fence, etc.).
The source holder may only be dismounted when the radiation is 

switched off. Make sure that the switch position " 

OFF

" is secured by 

a lock. 
Note chapters " 

Mounting

" and " 

Setup

" for dismounting and carry out 

the described steps in reverse order. 

8.2  Return, transport

Federal Republic of Germany

Contact the responsible sales engineer to arrange for a return, to 

check on the possibility of reuse or disposal.

Other countries

Contact the responsible sales partner to arrange for a return, to check 

on the possibility of reuse or disposal.
Also inform the relevant authority.
If a return in your country is not possible, contact the respective sales 

partner to decide on further action.
The destination airport for a possible return shipment is Frankfurt 

a. M., Germany.

Summary of Contents for VEGASOURCE 82









































































Reviews: