Vega VEGAPULS 69 Operating Instructions Manual Download Page 18

Page: 18 / 100

4 Mounting

VEGAPULS 69 • Modbus and Levelmaster protocol

47252-EN-210205

Fig. 6: Wall mounting with inclined wall via the mounting strap with length

300 mm

Two versions are available for mounting the instrument on a nozzle:

•

Combi compression flange

•

Adapter flange

Combi compression flange

The combi compression flange is suitable for different vessel flanges

DN 80, ASME 3" and JIS 80. It comes not sealed against the radar

sensor and can thus only be used unpressurized. It can be retrofitted

on instruments with single chamber housing, retrofitting to a double

chamber housing is not possible.

Fig. 7: Combi compression flange
1 Combi compression flange

Adapter flange

The adapter flange is available from DN 100, ASME 4" and JIS 100. It

is permanently connected with the radar sensor and sealed.

Flange

Summary of Contents for VEGAPULS 69





































































































Search results

Summary of Contents for VEGAPULS 69

Reviews:

Related manuals for VEGAPULS 69

Brands by name

Popular brands

Vega VEGAPULS 69, Operating Instructions Manual

Search results

Summary of Contents for VEGAPULS 69

Reviews:

Related manuals for VEGAPULS 69

Brands by name

Popular brands