VeEX VePAL TX300M User Manual Download Page 235

Page: 235 / 421

HDSL2 and HDSL4 Command Reference Table

Note

: Confirmation based on number of errors received.

User

The user code allows sending programmable codes of up to 16 bits (LSB first) and can be used for those codes or elements not

directly supported by the DS1 Loopback feature. Tap in the binary field and use the on-screen keypad to enter the binary

combination, and press the Apply button to return to the main screen. The Timeout field allows the user to set the exact time, in

seconds, in which the code will be sent and constantly repeated. User can adjust the period between 1 to 99 seconds. Entering

0 would send the loop pattern continuously until a new loop pattern is sent. A confirmation message will be displayed once the

time is up.

User Code

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands